What is the effect of issuing the BranchSw config if)# IPv6 address 2001 db8 a2b4 88:: 1 64 command?

A technician is configuring a new Cisco 2960 switch. What is the effect of issuing theBranchSw(config-if)# shutdown command?It disables a virtual or physical switch interface.It saves the running configuration to NVRAM.It activates a virtual or physical switch interface.It updates the MAC address table for the associated port.It saves the startup configuration to the running configuration.A technician is configuring a new Cisco 2960 switch. What is the effect of issuing the

Table of Contents Show

What is the effect of issuing the BranchSw?
What is the effect of issuing the BranchSw config if )# Exit command?
What is the effect of issuing the duplex full command?
What is the effect of issuing the BranchSw enable command?
What operational mode should be used on a switch port to connect it to a router for router on a stick inter VLAN routing?
How do you set up a Catalyst 2960 switch?
What is the effect of issuing the BranchSw config if )# shutdown command?
What is the effect of issuing the branches enable command?
What is the cause of the error that is displayed in the configuration of inter-VLAN?
What operational mode should be used on a switch port to connect it to a router for router on a stick inter-VLAN routing?
What is the effect of issuing the BranchSw config )# interface VLAN88 command?
What is the effect of issuing the shutdown command?
What is the effect of issuing the BranchSw config if)# exit command?
In what switch mode should port?
What is legacy Inter-VLAN routing?
What type of Ethernet cable would be used to connect one switch to another switch when neither switch supports the Auto MDIX feature *?
When Inter-VLAN routing is used How are the Switchports that link to the router configured?
How do you setup a Catalyst 2960 switch?
How do you initially configure a Cisco switch?
What is the default password for a Cisco 2960?
What is the default IP for Cisco Catalyst 2960?
What operational mode should be used on a switch port to connect it to a router for inter VLAN routing?
What is the effect of issuing the branches configure terminal command?
What is the effect of issuing the branches?

BranchSw(config-if)# shutdown command?A technician is configuring a new Cisco 2960 switch. What is the effect of issuing the

Get answer to your question and much more

BranchSw(config-if)# ipv6 address 2001:db8:a2b4:88::1/64 command?

Get answer to your question and much more

A technician is configuring a new Cisco 2960 switch. What is the effect of issuing theBranchSw(config-if)# exit command?

Get answer to your question and much more

A technician is configuring a new Cisco 2960 switch. What is the effect of issuing the BranchSw>enable command?It enters privileged mode.It enters the global configuration mode.It enters configuration mode for a switch virtual interface.It updates the MAC address table for the associated port.It permits an IPv6 address to be configured on a switch physical interface.

What is the effect of issuing the BranchSw(config-if)# shutdown command? It disables a virtual or physical switch interface.

What is the effect of issuing the BranchSw?

What is the effect of issuing the BranchSw# configure terminal command? It enters the global configuration mode. It enters configuration mode for a switch virtual interface. It applies an IPv4 address to the virtual interface.

What is the effect of issuing the BranchSw config if )# Exit command?

What is the effect of issuing the BranchSw(config-if)# exit command? It returns to global configuration mode.

What is the effect of issuing the duplex full command?

A technician is configuring a new Cisco 2960 switch. What is the effect of issuing the BranchSw(config-if)# duplex full command? It automatically adjusts the port to allow device connections to use either a straight-through or a crossover cable

What is the effect of issuing the BranchSw enable command?

What is the effect of issuing the BranchSw# configure terminal command? It enters the global configuration mode. It saves the running configuration to NVRAM.

What operational mode should be used on a switch port to connect it to a router for router on a stick inter VLAN routing?

What operational mode should be used on a switch port to connect it to a router for router-on-a-stick inter-VLAN routing? Explanation: Routers do not support Dynamic Trunking Protocol, and access mode is used to connect hosts.

How do you set up a Catalyst 2960 switch?

How to configure Cisco 2960 switch step by step?

Interface the hosts to the switch and arrange them.

Associate the switch to the switch and arrange the switch.

Arrange the switch.

Arrange the administration interface on VLAN 1.

Check the design of the switch.

Check availability utilizing ping and Telnet.

What is the effect of issuing the BranchSw config if )# shutdown command?

What is the effect of issuing the BranchSw(config-if)# shutdown command? It disables a virtual or physical switch interface. It updates the MAC address table for the associated port.

What is the effect of issuing the branches enable command?

What is the effect of issuing the BranchSwx26gt; enable command? It enters privileged mode. It enters the global configuration mode. It enters configuration mode for a switch virtual interface.

What is the cause of the error that is displayed in the configuration of inter-VLAN?

What is the cause of the error that is displayed in the configuration of inter-VLAN routing on router CiscoVille? The gig0/0 interface does not support inter-VLAN routing. The no shutdown command has not been configured. The IP address on CiscoVille is incorrect.

What operational mode should be used on a switch port to connect it to a router for router on a stick inter-VLAN routing?

What is the effect of issuing the BranchSw config )# interface VLAN88 command?

What is the effect of issuing the BranchSw(config-if)# shutdown command? It disables a virtual or physical switch interface. It updates the MAC address table for the associated port.

What is the effect of issuing the shutdown command?

What is the effect of issuing the BranchSw config if)# exit command?

What is the effect of issuing the BranchSw(config-if)# shutdown command? It disables a virtual or physical switch interface. It saves the running configuration to NVRAM.

In what switch mode should port?

In what switch mode should port G0/1 be assigned if Cisco best practices are being used? Explanation: The router is used to route between the two VLANs, thus switch port G0/1 needs to be configured in trunk mode.

What is legacy Inter-VLAN routing?

Legacy inter-VLAN routing In this method, multiple router interfaces are used, each connecting to a switch port in different VLANs. These interfaces are served as default gateways, which requires additional cabling when the network has to be expanded.

What type of Ethernet cable would be used to connect one switch to another switch when neither switch supports the Auto MDIX feature *?

3. What type of Ethernet cable would be used to connect one switch to another switch when neither switch supports the auto-MDIX feature? Explanation: A straight-through cable can be used to connect a computer or a router to a switch.

When Inter-VLAN routing is used How are the Switchports that link to the router configured?

One for each VLAN. The interfaces on the router are configured as the default gateways for the VLANs configured on the switch. The ports that connect to the router from the switch are configured in access mode in their corresponding VLANs

How do you setup a Catalyst 2960 switch?

How to configure Cisco 2960 switch step by step?

Interface the hosts to the switch and arrange them.

Associate the switch to the switch and arrange the switch.

Arrange the switch.

Arrange the administration interface on VLAN 1.

Check the design of the switch.

Check availability utilizing ping and Telnet.

How do you initially configure a Cisco switch?

How to configure Cisco switch?

Initial command prompt Switchx26gt; appears on the screen.

Type enable next to it and press Enter.

This will take you into the EXEC mode, also known as the Global Configuration mode.

Go into configure mode using configure terminal.

Enter the configuration commands one per line.

What is the default password for a Cisco 2960?

cisco

What is the default IP for Cisco Catalyst 2960?

10.0.0.1

What operational mode should be used on a switch port to connect it to a router for inter VLAN routing?

What is the effect of issuing the BranchSw(config-if)# shutdown command? It disables a virtual or physical switch interface. It updates the MAC address table for the associated port.

What is the effect of issuing the branches configure terminal command?

What is the effect of issuing the BranchSw# configure terminal command? It updates the MAC address table for the associated port. It permits an IPv6 address to be configured on a switch physical interface.